Dsmclubfinland.com
DSM tekniikka => Yleistä tekniikasta => Topic started by: Antti84 on February 02, 2008, 02:41:10 AM
-
Onko joku muukin 2G turboeclipsen omistajista viettänyt unettomia öitä
miettien jos auton kansi tulisi vaihtaa paremmin virtaavaan.. :)
Kun tulin tänne foorumille, moni "varoitti" mua käyttämästä tuota eclipsen
vakiokantta. Olinkin jo hetkeksi vaihtamassa kantta paremmin virtaavaan mutta onko "isompi aina parempi"?
Löysin ruotsin evokerhosta kiinnostavaa luettavaa EVOn(Eclipse 2G) ja GTI galantin kansista.
Itse en jaksa uskoa että Mitsubishin insinöörit olisivat laittaneet
"huonomman" kannen valmistuslinjan tehokkaimpaan malliin, ei
edes vaikka japsilaiseilla inssillä olisi juuri sillä hetkellä kakkulat
väärinpäin päässä. Mutta jos autosta aletaan ottamaan enemmän tehoa
(yli 500hv) tuo kannen vaihto galanttiin voisi olla ajankohtainen.
In a very basic sense, the larger VR4 intake ports actually taper dramatically at the valve causing less flow overall than the Evo head, which has a less dramatic step down.
You have to remember that even though you can assume that more volume will equal more power, the result is actually less flow. Porting plays with volume verses flow, the more meat you remove from the ports the slower the air flow will be (this is becuase you are creating less restriction). Carburattors use venturies (restrictions) to speed up air flow through the neck and into the combustion chamber.
What you need to know is that many people have proved the Evo head to be the better head for most applications. I say most becuase i have read articles where head porters have done extensive work to the VR head to make it just as successful as the Evo. Agian, the truth is hard to determine. Less overall work is required for the Evo head, making is the better platform for most builds.
I had a long conversation a few years ago with lyn rodgers about this very debate,the evo intake ports whilst smaller actualy flow the air faster and gets it into the head more effeciantly compared to the vr4 head.
if you want balls out quick drag car power then stick with the vr4 head,if you are keeping the mods simple to above average less than 5-600hp etc then go for the evo head.
Here's a simplification the way I see it.
Bigger ports = more maximum flow at the expense of mid/low rpm torque.
Smaller ports= better mid range at the expense of top end.
Air flows in pulses, it stops and starts, the "backpressure" caused by the momentum of the air (speed) helps to fill the cylinders.
Less speed =less backpressure=less VE at midrange rpms.
more speed = more backpressure= more VE.
If you're changing the size of the ports then maybe the length should also be changed? The same applies to exhausts.
-
2g turboissa on hieman "heikompi" kansi kuin on juuri vaikka 88-92 gti galantissa. Sama kansi löytyy 1g autoista. Useat vaihtavatkin 2g:hen 1g:stä kannen kun alkavat enempiä tehoja hakemaan.
Tämäkin on foorumilla tullut aikasemmin esille, mutta esimerkiksi imusarjoja vertaamalla, näet miten paljon isompi imupuoli on 1g:ssä (eli sama kuin noissa gti galanetissa) http://www.roadraceengineering.com/eclipsetech/headswap/1g2gheadswapintakemanifoldlg.jpg
-
Pitää paikkansa, kun kattoo tuota omaa imusarjaa, alkaa
melkein naurattaan ;D
No,saas nähdä mitä keksii,ehkä tuo kannen vaihto tulee joskus
ajankohtaiseksi..
-
2g turboissa on hieman "heikompi" kansi kuin on juuri vaikka 88-92 gti galantissa. Sama kansi löytyy 1g autoista. Useat vaihtavatkin 2g:hen 1g:stä kannen kun alkavat enempiä tehoja hakemaan.
Onko 2g vaparis se sama kansi ja imusarja ku turbos, eli pienempi?
-
2g turboissa on hieman "heikompi" kansi kuin on juuri vaikka 88-92 gti galantissa. Sama kansi löytyy 1g autoista. Useat vaihtavatkin 2g:hen 1g:stä kannen kun alkavat enempiä tehoja hakemaan.
Onko 2g vaparis se sama kansi ja imusarja ku turbos, eli pienempi?
On. (edm)
-
enkö tuomo joskus maininnu että hommaa hyvä mies 1g kansi :P
-
Sanoit vai? :) ei voi muistaa. Jos jollakin on ylim niin kannattaa tuputtaa tänne. Toisaalta noita gallun osia on aika paljon motonetis ja vastaavis. Onko muuten kaasuläppäkotelois eroja turbo/gti/4g63nt?
-
Onko muuten kaasuläppäkotelois eroja turbo/gti/4g63nt?
1g:ssä on isompi läppäkotelo kuin 2g turbossa. Turbon läppäkotelossa ei ole imuputkelle valmiiksi mitään jatketta, vaan siihen kiinnitetään oma mutkansa. Muita isoja eroja ei ole.